-
AeroRigid™291A aluminum honeycomb
AeroRigid™291A is a sandwich panel made with aluminum facing and 3.4 lbs/ft3 aluminum honeycomb that is designed for aircraft interior structural and nonstructural applications such as monuments, shelving, partitions, bulkheads and galleys. Manufactured by Showa Aircraft and distributed by Professional Plastics USA, Singapore & Taiwan. ISO and AS9100 approved supplier.
- 291A is an AeroRigid 2024 Aluminum Honeycomb Epoxy with .250" Cell and 3.4 Density
-
Makrofol® DE 7-2 Polycarbonate Film
Makrofol® DE 7-2 Velvet-Fine Matte Polycarbonate Film - Makrofol DE 7-2 is a translucent
polycarbonate film that minimizes pin holing and offers a unique combination of low gloss and
enhanced abrasion resistant features. This textured polycarbonate film is supplied with a Velvet first surface
and a Very Fine Matte second surface. Makrofol DE 7-2 is offered in thicknesses from .005" to .030".
- Dazzle-free, scratch resistant
- As 6-2 but coarser Velvet texture on one side.
- UL94 VTM-2 & FMVSS 302
- Compares to Lexan 8B38
-
Meldin® 7211 15% Graphite + 10% PTFE
Meldin® 7211, 15% by weight graphite and 10% by weight PTFE fillers (comparable to Vespel SP-211). It has the lowest coefficient of friction of all the Meldin® 7000 series grades. However, above 300°F, we typically suggest using Meldin® 7021, which has a very similar coefficient of friction to 7211 at temperatures above 300°F, and the wear factor of 7021 is lower than 7211 at temperatures above 300°F.
-
Nycast® XHA-BLUE - Heat Stabilized
NYCAST® XHA-BLUE has a heat stabilizer that retards the loss of physical properties as temperature increases. This allows the material to function at approximately 10% higher temperatures than standard grades; meaning NYCAST XHA operating at 200° F will have approximately the same physical properties as a standard grade operating at 185° F. Maximum intermittent temperature for NYCAST XHA is 330° F and continuous operating temperature is 250° F (compared to 230° F for standard grades).
-
Nylatron® LIG - Oil-Filled Nylon
Nylatron® LIG combines the toughness of cast PA6 with an oil-based lubricant that is encapsulated within the nylon matrix. It increases the load bearing performance of the material when compared to unfilled nylons and reduces the coefficient of friction. It is an ideal material for industrial application.
-
Nylatron® GSM Blue Nylon (MD+Oil)
Nylatron® GSM Blue Nylon
The first cast nylon to combine both molybdenum disulphide (MoS²) (aka MD) and Oil for the load capacity of Nylatron GSM nylon, plus improved frictional characteristics. It excels in higher pressures, and at low speeds-up to 40 fpm. It offers 20% lower coefficient of friction, 50% greater limiting PV, and a lower "k" factor than Nylatron GSM, and the lowest "slip-stick" of any nylon product making it ideal for slide pads, thrust washers and trunion bearings.
- Color: Dark Blue
- Filled with MD + Oil
-
Nylon®, Oil-Filled - Green (Generic)
Oil-Filled Nylon (green Color): - A special formulation of Liquid Lubricant encapsulated during manufacture, provides for true lubrication at the bearing surface. It is offered for applications where maintenance lubrication is difficult or impossible. Oil-filled Nylon also, limits moisture adsorption, making it an ideal bearing material for submerged or critical tolerance applications.
- Also See Nyloil® Green
- Oil-Filled Nylon is also available in NATURAL-OIL for Food Contact applications. The absence of Pigment (NATURAL COLOR) permits this grade to conform with FDA Regulations 21 CFR, Sec. 177.15 and USDA 3A Sanitary Standards 20-17 for direct contact with food. See Nyloil FG Food Grade
-
Nylon, Oil-Filled - Natural (Generic) FDA
Oil-Filled Nylon in NATURAL Color for Food Contact applications. The absence of Pigment (NATURAL COLOR) permits this grade to conform with FDA Regulations 21 CFR, Sec. 177.15 and USDA 3A Sanitary Standards 20-17 for direct contact with food.
Typical Applications:
- FDA Compliant Bearings and Bushings
- Replacement for Stainless Steel in Food Processing Applications:
- Bottling, Canning, Packing, Processing Lines
- Friction / Wear Parts
- Gears, Sprockets and Rotational Parts
-
![Semitron® ESd 420 - ESd PEI (ULTEM)]( "Semitron® ESd 420 - ESd PEI (ULTEM)")
Semitron® ESd 420 - ESd PEI (ULTEM)
Semitron® 420 is stocked in our USA, Singapore and Taiwan Warehouses. Semitron ESd 420 Static Dissipative PEI is the only, truly dissipative plastic product for use in high temperature applications. This material offers a unique combination of properties including: static dissipation, low coefficient of expansion, high strength and heat resistance and is non-sloughing. ESd 420 has a tensile modulus of 550,000 psi, a heat deflection temperature (at 264 psi) of 420°F, and a surface resistivity in the intermediate range of 106 to 109 ohms/square (W/sq.).
Semitron stock shapes for machining, is ideal for making fixtures for handling silicon wafers and devices in equipment for manufacturing semiconductor devices.
- Semitron 420 is stocked in our USA, Singapore and Taiwan Warehouses
Semitron® ESd 420 is also ideal for use in equipment for handling components in the hard-drive manufacturing and assembly processes. Semitron® ESd 420 also has a low coefficient of thermal expansion, high compressive strength and good wear resistance. MCAM-Quadrant Semitron® ESd 420 shapes have very low residual stresses and as a result can be machined very flat and to very tight tolerances. Perhaps most importantly Semitron® ESd 420 is non-sloughing. As a result, it does not particulate significantly in these handling applications. Wafer combs and other parts for handling sensitive electronic components must be dissipative. More importantly they must be capable of discharging static electricity in a controlled manner. An uncontrolled discharge event can lead to damaged product. Semitron® ESd 420, which has a surface resistivity of 106 to 109 Ohms/sq., is ideal for use in such applications. Semitron 420 reliably meets all physical performance needs for wafer combs and other handling components, combined with stable ESd performance.
-
Techtron® HPV - Bearing Grade PPS
Techtron HPV is an extruded form of polyphenylene sulfide with reinforcement and internal lubricants, offering excellent wear resistance, strength, dimensional stability and chemical resistance. Techtron HPV is an ideal material for applications where standard engineering plastics (nylon, acetal, and polyesters) fall short, and advanced materials (polyimides, PEEK, and polyamide-imides) are over-engineered solutions.
- Note: Rods are sold in Standard 1 meter lengths (3.28 feet) (39.3 inches)
-
Torlon® 4XG - Extruded (30% G/F)
Torlon 4XG PAI is a 30% glass-reinforced PAI (polyaminde-imide). It offers high rigidity, retention of stiffness, a low expansion rate and improved load carrying capabilities. This grade is well suited for applications in the electrical/electronic, business equipment, aircraft and aerospace industries. Torlon 4XG is the extruded version of Torlon 5030, as made by MCAM-Quadrant EPP. Torlon 5530 is the compression-molded version of this same product. Both Torlon 4XG and Torlon 5530 are made from a base 30% glass-filled Torlon resin manufactured by Solvay as Torlon 5030 (5030 resin is used for injection-molding). Torlon is a registered trade name of Solvay Advanced Polymers.
-
![Torlon® 5530 (30% Glass-Filled PAI)]( "Torlon® 5530 (30% Glass-Filled PAI)")
Torlon® 5530 (30% Glass-Filled PAI)
Torlon® 5530 (30% glass-filled polyamide-imide) is MCAM-Quadrant's compression-molded version of Solvay Torlon 5030 PAI injection-molding resin. The compression-molding process creates a random dispersement of the glass fibres which in-turn allows for tremendous dimensional stability in all directions (as compared to unidirectional glass-fibre flow created through injection-molding and extrusion. In addition to strength and dimensional stability, Torlon® 5530 is electrically insulative with a surface resistivity of > 1013 Ohms/sq. It has exceptional dielectric strength- over 800-volt/ mil. It offers best- in- class radiation resistance, withstanding exposure to 10 x 9th rads*. Close tolerance components are produced from Torlon 5530 including IC Test Sockets, Handlers & Nests welding tip insulators, CVT clutch rollers, fasteners, igniter cups & cases, gears, splines, hydraulic poppets and many other structural and dynamic components. - Limitations: Only manufactured in Plates (maximum plate size: 14" x 28").
- For Rods or Extruded product from the same resin, try Torlon 4XG
- Torlon 5530 is stocked in the USA Singapore & Taiwan.
-
![Two-Way See Through Surveillance Mirror]( "Two-Way See Through Surveillance Mirror")
Two-Way See Through Surveillance Mirror
See Through Mirror - aka "Two-Way Mirror" Transparent, See-through Mirrors (Surveillance Mirror) is available in either Acrylic 2 way mirror, or Polycarbonate 2 way mirror (for increased impact-resistance). Two way mirrors look like a mirror from one side and a window from the other side when correctly lit. You can only see through the mirror when the area you are looking from is darker then the area you are looking into. Works best when there is no light on the viewing side. When the light is equal on both sides it appears as a mirror but you can also see through to the other side.
1/8 " (.125") or 1/4" (.250") Mirror-Grade Acrylic or polycarbonate is coated with a 2-way Mirror Finish. Looks like a Mirror from the lighted side and a Window from the side with little or no light. Perfect for surveillance for a Show Room or Store from an Office. Can be used to hide surveillance cameras to monitor store activity. Used in Many Non-Security Related Crafts.
Note: Because acrylic and polycarbonate are flexible, we recommend the .250" thick for mirrors larger than 24" x 48" in size.
-
ULTEM™ 2300 - 30% Glass-Filled
ULTEM™ 2300 PEI is an extruded 30% glass reinforced polyetherimide. It is an amorphous, high-performance polymer with exceptional flame and heat resistance. It performs continuously to 340°F (171°C), making it ideal for high strength/high heat applications, and those requiring consistent dielectric properties over a wide frequency range. It is hydrolysis resistant, highly resistant to acidic solutions and capable of withstanding multiple autoclaving cycles.
ULTEM™ 2300 provides greater rigidity and improved dimensional stability while maintaining many of the useful characteristics of unfilled ULTEM™. ULTEM™ is commonly machined into parts for reusable medical devices, analytical instrumentation, electrical/electronic insulators, and a variety of structural components requiring high strength and rigidity at elevated temperatures.
- Stocked at Professional Plastics USA, Singapore & Taiwan Warehouses
-
![Ceramatest™ 500 - Mica-Filled Ceramic]( "Ceramatest™ 500 - Mica-Filled Ceramic")
Ceramatest™ 500 - Mica-Filled Ceramic
Ceramatest™ 500 is a glass bonded sythetic mica ceramic material designed to meet the exacting demands of technical markets. This material is a versatile and efficient electrical and thermal insulating material. Ceramatest 500 is a fully inorganic material used to bridge the performance gap between high performance plastics and structural ceramics. Ceramatest 500 glass bonded mica ceramic is a simultaneous union under high pressure and temperature of finely powdered electrical quality glass and precisely defined (natural or synthetic) mica. The resulting stone-like, dense ceramic material inherits all of the insulating advantages of both components.
Ceramatest™ is available in several machinable grades suitable for processing with standard carbide tools and water (or a water based lubricant) and in moldable grades that do not require firing or sintering after molding. As a result, the material can accommodate metal inserts during molding similar to thermoplastics. CeramaTest™ does not burn or outgas. The material is dimensionally stable at elevated temperatures
- Max. Continuous Use Temperature is 930° F (500° C)
- Ceramatest™ 500 is LIGHT GREY in Color
-
Delrin® AF Blend - 13% PTFE (Standard)
Delrin® AF Blend (Delrin® AF Blend with13% PTFE [Standard Grade] ) Delrin AF Blend is a unique thermoplastic material for use in moving parts in which low friction and long wear life are important. It is a combination of PTFE fibers uniformly dispersed in Delrin® acetal resin.
- Delrin® AF Blend typically includes 13% PTFE Fibre-Filled
- LF-13 is always a 13% PTFE Powder-Filled.
- Also available in Full-Strength Delrin 100AF - 20% PTFE on a Custom Order Basis.
- DE588 is a Delrin® 100AF fully-certified for US Naval Specifications.
-
Durostone® Wave Solder Pallet Material
Durostone® wave solder pallet materials have excellent mechanical properties at elevated temperatures. These products have become the industry standard for the production of wave solder pallets used in the printed circuit board industry.
Durostone is easier to handle in the production process than other products used for PCB tooling due to two factors:
- The density, which helps to reduce the weight of the finished tooling.
- The glass and resin content, which ensures that the line operators and the machinists are not subjected to skin irritation alleviating any health & safety concerns.
Durostone® is Produced in Three Standard Grades:
- CHP 760 (Blue) (Standard)
- CAS 761 (Black) (Anti-Static)
- CAG 762 (Grey) (Anti-Static, Optical)
Other Durostone® Specialty Grades:
- CFR 762 (Black)(Flux-Resistant) - For Harsh Environments
-
![G-30 Polyimide Glass Laminate (Norplex P95)]( "G-30 Polyimide Glass Laminate (Norplex P95)")
G-30 Polyimide Glass Laminate (Norplex P95)
G-30 polyimide glass laminate (aka Norplex P95 per NEMA GPY) is a high performance woven glass fabric bonded with polyimide resin. Specially developed to provide engineers with a plastics material capable of continuous long term use at 500°F and higher. Possesses excellent dimensional stability, mechanical and electrical properties which are well maintained at elevated temperatures. Has machining characteristics similar to Grades G10 and G11. G30 (aka Norplex P95-GPY) consists of woven glass fabric with polyimide resin. The product is engineered to maintain excellent physical properties at 240°C, making it suitable for high-temperature applications. It offers a low coefficient of thermal expansion, as well as high mechanical strength and consistent quality. It can be used for structural components, thermal insulators, PCB manufacture and assembly, and high-temperature gaskets in petrochemical plants. P95 complies with the requirements of IEC 60893-3-7-PI GC 301.
-
Meldin® 7022 Polyimide (40% Graphite-Filled)
Meldin® 7022, 40% by weight graphite filler (comparable to Vespel® SP-22) - Meldin® 7022 is similar to the Meldin 7021 for wear and friction, but it has the best overall dimensional stability (thermally), and the 7022 has the lowest coefficient of thermal expansion — due to the relatively high graphite filler content.
Meldin 7000 series polyimides are formed using high-pressure mold presses, automatic resin-feeding systems, and computer-controlled hydraulics. Complex shapes can be molded, reducing the need for secondary machining operations. The Meldin 7000¡ series features operational temperatures of 600ºF for continuous operation and 900ºF for intermittent exposure, and tight tolerances of ±0.001 in. on both ODs and IDs.
-
|
Contact Us
Locations
About Us
Track Shipment
Register
Log In
