-
Face Mask - N95 Respirator - Industrial - Teal - CS-06
Face Mask - N95 Respirator - Industrial - Teal - Cup Style - Model PT-N95C/CS-06 "molded" industrial N95 Respirator with Metal Nosepiece.
- Part Number CS-06 (Teal)
- NIOSH Industrial Approved - Model TC-84A-9281 (Regular), TC-84A-9280 (Small)
- NIOSH approved N95 rating
- Meets NIOSH inhalation procedure testing TEB-APR-STP-0007.
- Fluid Resistant 160 mmHg.
- Flammability Rating Class I.
- Adjustable nose clip.
- Braided and stapled headbands.
- >/=95% BFE (Bacterial Filtration Efficiency) according to ASTM F2101.
- >/=95% Filter Efficiency according to ICS Laboratories Inc.
- Pre-formed for secure fit and for easy breathing.
- Bendable nose clip will help provide custom and secure seal.
- Available in Small and Large.
- Latex free: Yes.
- Model: Collapse Resistant Cup/Procedure.
-
FEP Rods & Sheets
FEP Rods & Sheets
FEP is a relatively soft thermoplastic with lower tensile strength, wear resistance, and creep resistance than many other engineering plastics. However, FEP is chemically inert and has a low dielectric constant over a wide frequency range. FEP possesses a very high degree of stress crack resistance, a low coefficient of friction, exceptional dielectric properties, heat resistance, retention of properties after service at 400°F (204°C) with useful properties at -454°F (-270°C), and meets FDA 21CFR.177.1550. FEP has high transparency (with good transmittance of UltraViolet and visible wavelengths.) FEP offers the lowest refractive index of all thermoplastics with low light reflection (the same as water.)
- FEP stands for Fluorinated Ethylene Propylene.
-
FEP Shrink Tubing 1.3:1 & 1.6:1
FEP heat shrink tubing is a common alternative to PTFE, with similar electrical and friction properties and chemical resistance. FEP heat shrinkable tubing conforms to Mil-I-23053/11, and UL 94 (V0, VW-1), and is suitable for continuous use at temperatures up to 204°C.
FEP heat shrink tubing is used in cases where temperatures are not as extreme, and very high shrink ratios are not necessary. It is also widely used when components cannot handle the extreme shrink temperature of PTFE. It is available in 1.6:1 and 1.3:1 varieties, shrinks at around 190-210°C, and has found widespread use and appeal.
-
FEP Tubing - Convoluted/Corrugated
Convoluted FEP Tubing (aka Corrugated FEP Tubing) is supplied by Professional Plastics in a full range of sizes. Brands include Corrtef® FEP corrugated tubing.
Typical Applications:
- Chemical Processing - Corrosive Environments - Deionized Water - Hot Glue - Laboratory Uses - Paint Spray - High Purity Fluid Transfer - Solvent Transfer
- Maximum overall available length (FOR CUFFED TUBING): 12 feet (including cuffs)
- Specify Overall Lengths (including cuffs) when ordering. - see flyer for sizes and cuff lengths
- Non-Cuffed Tubing may be available in longer lengths
-
FEP Tubing
FEP tubing (Fluorinated Ethylene Propylene tubing) is made from a melt processable thermoplastic that has end uses similar to PTFE. However, it has several properties PTFE does not have. FEP is one of the clearest plastics available on the market and FEP tubing can be supplied in long, continuous coils. Also, it can be welded and tubes can be sealed by melting. FEP tubing has a continuous working temperature of 400° F (204°C).
-
FluoroPro™ PCTFE
FluoroPro™ PCTFE(PolyChloroTriFluoroEthylene) is a fluorocarbon-based polymer and is commonly abbreviated PCTFE. PCTFE offers the unique combination of physical and mechanical properties, nonflammability, chemical resistance, near zero moisture absorption, and excellent electrical properties. These characteristics cannot be found in any other thermoplastic fluoropolymer with a useful temperature range of -400°F to +400°F. PCTFE also has extremely low outgassing, making it well suited for use in aerospace and flight applications.
- Standard Extruded Rod Lengths are 6 Feet Long (1828mm) - rods can be cut as needed
- Compression-Molded Rods are typically 1 Foot Long (305mm)
-
FluoroPro™ PFA Rods & Sheets
FluoroPro™ PFA Rod and FluoroPro™ PFA Sheet
PerFluoroAlkoxy (PFA) offers similar properties to FEP, but PFA is preferred when extended service is required in hostile environments involving chemical, thermal, and mechanical stress. PFA offers high melt strength, stability at high processing temperatures, excellent crack and stress resistance, a low coefficient of friction, and more than 10 times the Flex life of FEP. It has high resistance to creep and retention of properties after service at 500°F (260°C), with useful properties at -320°F (95°C). PFA also meets FDA 21CFR.177.1550.
-
![Fluorosint® HPV]( "Fluorosint® HPV")
Fluorosint® HPV
Fluorosint® HPV PTFE - Most Wear Resistant Fluorosint Grade - Outlasts Low-tech PTFE Based Materials
FDA-compliant Fluorosint HPV is a mica-filled high-performance bearing grade that can deliver a pressure velocity (PV) performance improvement of more than 40 per cent over other PTFE materials according to in-house tests conducted by MCAM-Quadrant. Parts made of Fluorosint HPV can withstand higher loads and velocities while delivering better wear resistance, enabling the part to last longer compared to existing FDA-compliant PTFE-based materials. The product was specially developed to meet the demands of high-performance bearing applications where other, low-technology PTFE formulations would exhibit premature wear or not perform adequately. These characteristics, together with FDA compliance for food and pharmaceutical applications, open up interesting new options for engineers and manufacturers. Simply put, parts machined from Fluorosint HPV last longer than those made from many of the alternative filled PTFE materials on the market today. Fluorosint HPV can replace bronze, steel and powdered metal parts and deliver performance gains in wear life and system performance. Typical applications include thrust washers, wear guides, seals and food processing and preparation equipment.
FDA compliant Fluorosint HPV PTFE is a high performance bearing grade of Fluorosint - optimized for high PV and very low "K" or wear factor. Fluorosint HPV PTFE was developed for bearing applications where other, low-tech PTFE formulations exhibit premature wear or simply cannot perform. FDA compliance gives food and pharmaceutical equipment manufacturers new design options and all benefit from its excellent load bearing and wear characteristics.
-
![FRP Wall & Ceiling Panels & Profiles]( "FRP Wall & Ceiling Panels & Profiles")
FRP Wall & Ceiling Panels & Profiles
FRP Panels (fiberglass reinforced plastic) FRP wall and celiling panels are available from Professional Plastics. We are a distributor of Sequentia brand FRP & can cross-reference other brands if necessary (click here to view FRP Cross Reference Chart) Structoglas FRP, is an easy-to-clean wall and ceiling panel made of fiberglass reinforced plastic. Structoglas will not rot, corrode, stain, dent, peel, or splinter in the toughest conditions. Structoglas panels install as easily as common wall board on solid substrates. Structoglas is available in different colors and finishes, and can be cut and drilled for easy installation. Accessories such as moldings and rivets are also available to complete the installation.
Class A Fire Rated Embossed
Structoglas FRFR -
Many building codes require that interior finish products meet a Class A, B, or C fire rating. This is defined by flame spread and smoke development and the test results determine how the product is rated. The lower the flame spread and smoke development, the higher the rating.
Structoglas FRFR (Class A fire rating) is accepted by all major building codes for use where fire ratings require a Class A rating - per the ASTM E-84 test method.
Class C Fire Rated Embossed
Structoglas FTST -
Many building codes require that interior finish products meet a Class A, B, or C fire rating. This is defined by flame spread and smoke development and the test results determine how the product is rated. The lower the flame spread and smoke development, the higher the rating.
Structoglas FTST panels (Class C fire rating) meet all minimum building codes and USDA/FSIS requirements.
Class A Fire Rated Smooth
Structoglas FSI -
Structoglas FSI (Class A fire rating) has a smooth finish and is acceptable for use as wall and ceiling panels.
Class C Fire Rated Smooth
Structoglas FSQ -
Structoglas FSQ (Class C fire rating) has a smooth finish and is acceptable for use as a wall and ceiling panel.
Class C Fire Rated Pre-Laminated Panels
Structoply
Structoply is fabricated by laminating a Structoglas frp panel to a rigid substrate, such as oriented strand board (OSB), plywood, or fluted polypropylene. The resulting Structoply panel has structural strength and rigidity, allowing fast and easy installation directly to studs on the wall or ceiling.
Structoply is used in a wide variety of applications where durability and ease of installation are a must.
Titebond® FRP Adhesive
Number One Recommended Adhesive in the Industry!
Formulated with proprietary emulsion polymers specifically designed for FRP substrates
Vinyl Moldings
For professional looking panel installations, and maximum moisture sealing effectiveness, use Structoglas color coordinated, non-staining vinyl moldings and rivets.
-
G-10/FR-4 Sheets
G-10/FR-4 is a thermosetting industrial laminate consisting of a continuous filament glass cloth material with an epoxy resin binder. It has characteristics of high strength, excellent electrical properties and chemical resistance not only at room temperature but also under humid or moist conditions.
- aka G10/FR4, G-10/FR4, FR4 Glass-Epoxy Laminate Sheets
- G-10/FR-4 glass epoxy laminate meets the specifications of Mil-I-24768/27
- G-10 & FR-4 also meet LP 509 & MIL P 18177 Type GEE
- Maximum Continuous Operating Temperature: 285°F
-
Glastherm HT200
Glastherm HT200 is a thermal insulating sheet with superior strength and heat resistance for applications with continuous use temperatures up to 550º F. The installation or upgrading of mold base or press platen insulation is one of the highest-returning investments a molding operation can make today. Properly insulated molds require less energy to operate. Adequate insulation also facilitates temperature regulation within the tool.
Glastherm® thermal insulating sheet is an excellent choice for mold insulation applications. Glastherm® sheet offers significant advantages when compared with other materials such as mica, asbestos concrete or calcium silicate. Glastherm® sheet is an efficient thermal barrier and is strong to resist the effects of molding pressure and rough handling. It is resistant to oil and water absorption and is completely asbestos-free.
-
GPO-3 Angle
GPO-3 Angle is available in equal leg angle, and unequal leg angle. GPO-3 performs well in electrical applications that require high arc and carbon track resistance as well as flame resistance, physical strength, and moderate heat resistance. Grade GPO-3 laminate is used extensively in the making of phase and end barriers, insulating supports, bus bar supports and mounting panels in switchgear and other types of electrical apparatus. Grade GPO-3 s a UL recognized product with a temperature index of 120 degrees celsius electrical and 140 degrees celsius mechanical. In addition to outstanding electrical properties, these GPO3 angles have a high strength-to-weight ratio, and are UL Recognized and flame, arc and track resistant.
-
![GPO-3 Sheets]( "GPO-3 Sheets")
GPO-3 Sheets
GPO-3 glass reinforced thermoset polyester sheets, also known as "Red Barrier Board" in construction applications. GPO-3 laminate performs well in electrical applications that require high arc and carbon track resistance as well as flame resistance, physical strength, and moderate heat resistance. GPO-3 laminate is used extensively in the making of phase and end barriers, insulating supports, bus bar supports and mounting panels in switchgear and other types of electrical apparatus. GPO-3 is a UL recognized product with a temperature index of 120 degrees celsius electrical and 140 degrees celsius mechanical, and is molded in thicknesses of 1/32" (.031") to 2.00" thick. GPO-3 is produced in Standard Color RED, or specialty colors Black, and White. and is molded in thicknesses of 1/32" (.031") to 2.00" thick.
- H900 is the standard GPO-3 Grade supplied by Professional Plastics (see datasheet for details)
- GPO-3 is also sold by Professional Plastics in a variety of profiles including angles, and channels.
-
![Hastelloy® C-276]( "Hastelloy® C-276")
Hastelloy® C-276
HASTELLOY® C-276® is a wrought corrosion-resistant alloy. A prime advantage of this alloy is that it generally does not require solution heat treatment after welding. Hastelloy resists the formation of grain boundary precipitates that would degrade corrosion resistance. Alloy C-276 offers improved fabricability over the similarly corrosion-resistant Alloy C. Conventional methods can be used to hot work and cold form Alloy C-276, and typical welding techniques are appropriate. Resistant to forming grain boundary precipitates in the weld-affected zone, Alloy C-276 is appropriate in the as-welded condition for many chemical processes. Other benefits include resistance to pitting, stress-corrosion cracking and oxidation to 1900° F (1038° C).
Hastelloy® C276 is used for rotors, bolts, shafts, blades and other components in marine applications and other industries, including pollution control; food, waste and chemical processing; paper operations; and multipurpose plants. Tungsten has been added to this versatile nickel-chromium-molybdenum alloy, which resists crevice corrosion, stress corrosion cracking, and pitting. Resistant to chloride ions and sulfur blends, Hastelloy C 276 is ideal for flue gas desulfurization applications.
Hastelloy C 276 (also known as UNS N10276) is available from Professional Plastics in the following:
- Sheet/Plate - ◦ ASTM-B-575 ◦ ASME-SB-575
- Bar/Forgings - ◦ ASTM-B-575 ◦ ASME-SB-575
- Supplier with 22 locations in USA, Singapore and Taiwan.
-
HDPE Rods
HDPE Rods (round bars) - High-density polyethylene rods offer excellent impact resistance, light weight, low moisture absorption, and high tensile strength. HDPE Rods are also non-toxic and non-staining and meets FDA and USDA certification for food processing.
- Standard Colors: Natural (milky white) & Black
- Other Colors available on a customer order basis.
-
-
HDPE Sheets
HDPE (high-density polyethylene) (AS EXTRUDED) offers excellent impact resistance, light weight, low moisture absorption, and high tensile strength. HDPE is also non-toxic and non-staining and meets FDA and USDA certification for food processing.
- Sheets Sold on this Page are AS EXTRUDED
- Also Available in Stress-Relieved (S/R)
-
HDPE Tubing
High Density Polyethylene (HDPE) Tubing HDPE tubing is less flexible than LDPE, but has better physical and chemical properties, and withstands sterilization by boiling. It is widely used in transporting air, water and chemicals. It is produced from raw materials which meet FDA requirements. NSF 51/61 also available.
HDPE Tubing Colors: Natural (semi-opague white) & Black (specific sizes) - The color black is good for improved durability in direct sunlight and outdoor exposure.
Custom Colors also available with Minimum Order Quantities
Standard Coil Length: 100 Feet (30.5 meters) - Cut pieces & special lengths on custom basis.
- For best results, use sleeved compression fittings with all thermoplastic tubing.
-
High-Impact Polystyrene - HIPS
High Impact Polystyrene (HIPS) has great dimensional strength, balanced properties of impact strength and heat resistance, is easily machined, and is relatively low in cost.
- Styrene is available in standard 48" x 96" sheets, or Custom Sheets & Rolls
- Also available in Conductive Grades upon request.
-
![Kel-F® - PCTFE]( "Kel-F® - PCTFE")
Kel-F® - PCTFE
Kel-F - PCTFE (PolyChloroTriFluoroEthylene) Kel F is a fluorocarbon-based polymer and is commonly abbreviated PCTFE. PCTFE offers the unique combination of physical and mechanical properties, nonflammability, chemical resistance, near zero moisture absorption, and excellent electrical properties. These characteristics cannot be found in any other thermoplastic fluoropolymer with a useful temperature range of -400°F to +400°F. PCTFE also has extremely low outgassing, making it well suited for use in aerospace and flight applications. Note: Kel-F® is a registered tradename of 3M Company. In 1996, 3M discontinued manufacturing of Kel-F & today, all PCTFE resin is manufactured by Daikin under the tradename of Neoflon ® or by Allied Signal under the tradename of Aclon ®. Kel-F is still the most commonly used tradename used to describe PCTFE.
- Standard Extruded Rod Lengths are 6 Feet Long (1828mm) - rods can be cut as needed
- Large Diameter Compression-Molded Rods & Tubes are typically 1 Foot Long (305mm)
- There is currently a Global Shortage of PCTFE Resin & Products - Please send your request ASAP & we will do our best to support your needs.
|
Contact Us
Locations
About Us
Track Shipment
Register
Log In
