-
Fluorosint® 207
Fluorosint® 207's unmatched dimensional stability, excellent creep resistance and white color uniquely position this material to serve FDA regulated applications. It is non-permeable in steam and complies with the FDA's regulation 21 CFR 175.300. Its relative wear rate is 1/20 the rate of PTFE below 300°F (150°C) making it an excellent choice for aggressive service bearings and bushings.
Fluorosint is Now Available in 5 Grades:
- Fluorosint® 207 - Lowest Coefficient of Friction of all Fluorosint Grades
- Fluorosint® 500 - Exceptional Dimensional Stability for Precise Tolerance Control
- Fluorosint® HPV - Most Wear Resistant Fluorosint Grade - Outlasts Low-tech PTFE Based Materials
- Fluorosint® 135 - Superior Performance Grade For Stability In Extreme Conditions
- Fluorosint® MT-01 - Ultra-High Performance Fluorosint Grade For Stability At Elevated Temperature
-
![Fluorosint® 500]( "Fluorosint® 500")
Fluorosint® 500
Fluorosint® 500 has nine times greater resistance to deformation under load than unfilled PTFE. Its coefficient of linear thermal expansion approaches the expansion rate of aluminum, and is 1/5 that of PTFE — often eliminating fit and clearance problems. It is 1/3 harder than PTFE, has better wear characteristics and maintains low frictional properties. Fluorosint® 500 is also non-abrasive to most mating materials.
- Sizes in drop-down menus are in INCHES
- Applications: Bearings - Seals - Mixers - Pumps - Appliances - Valve seats
Fluorosint is Now Available in 5 Grades:
- Fluorosint® 500 - Exceptional Dimensional Stability for Precise Tolerance Control
- Fluorosint® 207 - Lowest Coefficient of Friction of all Fluorosint Grades
- Fluorosint® HPV - Most Wear Resistant Fluorosint Grade - Outlasts Low-tech PTFE Based Materials
- Fluorosint® 135 - Superior Performance Grade For Stability In Extreme Conditions
- Fluorosint® MT-01 - Ultra-High Performance Fluorosint Grade For Stability at Elevated Temperature
-
Flx-Thane SD Tubing (ESd Urethane)
Flx-Thane SD Tubing (ESd Polyurethane Hose) from Flexaust is a Medium weight Clear or Black static dissipative polyurethane hose reinforced with a bronze coated spring steel wire helix.
- Standard Color is Clear
-
![Formex GK - FR Sheets]( "Formex GK - FR Sheets")
Formex GK - FR Sheets
Formex GK Sheets
Formex™ GK materials are used in order to comply with UL, CSA, IEC, VDE, TUV, BSR or MITI standards when there is a need for electrical insulators and barriers. This unique product line has successfully replaced a variety of flame retardant sheet materials including polycarbonate, polyester, PVC and aramid papers.
Formex GK-17 & Formex GK-17BK
- 0.017 inch thick - Standard Sheet Size is 24" x 48", Also Available in Longer Rolls
- Superior dielectric strength
- Continuous use temperature to 115°C / 239°F
- Score and fold to fabricate economical 3-D parts
- Fold repeatedly without cracking or splitting
- High dielectric breakdown strength
- UL 94 V-0 flame class & RoHS compliant
- Non-hygroscopic & Superior Chemical Resistance
- Also Available In:
- Formex GK-10 & Formex GK-10BK (.010" thick)
- Formex GK-30 & Formex GK-30BK (.030" thick)
- Formex GK-40 & Formex GK-40BK (.040' thick)
- Formex GK-62 & Formex GK-62BK (.062 thick)
- Formex GK-160 PEP (.160" thick)
- Formex GK-240 PEP (.240" thick)
-
FRP-3 Sheet - FM 4910 FRPP
FRP-3 Sheet - FM 4910 FRPP - Simona LAM FRP-3 | FM 4910 Listed Flame-Retardant Polypropylene Sheet
Specifically developed to meet the FM 4910 clean room fire test, LAM FRP-3 performs well in cabinetry and enclosures in low acid environments such as rinse modules, wafer transfer interfaces and UPW modules. As with any FM4910 polypropylene-based material, it is not recommended for use in concentrated acids, or aromatic, aliphatic or chlorinated solvents. This white, flame-retardant sheet offers excellent color consistency and delivers a good balance of cost and performance for cabinets and dry tool area applications.
Proven Applications:
- Semicon cabinets with low acid exposure
- Rinse modules
- Electrical cabinets
- Alkaline, UPW modules
- Wafer transfer interfaces
- Dry tool areas
-
G-10 Non-Brominated
NEMA Grade G10 materials are continuous filament woven fiberglass sheets bonded
with epoxy resin. The material has the ability to maintain excellent mechanical, electrical,
and physical properties at elevated temperature to 130C. NEMA G-10 is a non-brominated,
non-flame retardant grade of glass epoxy laminate.
- Non-Brominated G-10 meets Mil-I-24768/2.
- Non-Brominated G-10 contains no halogens & is available as a Custom Order Only & is only rated as UL94-HB.
-
G-10/FR-4 Copper Clad Sheet
Copper Clad FR-4 - PCB Laminate Sheet
This flame retardant copper-clad laminate is made of continuous woven glass cloth impregnated with epoxy resin. The substrate is made of FR4 which is a flame retardant version of G-10 material. Copper Clad FR-4 Sheet is used to created printed circuit boards.
- .059" is most common thickness.
-
G-10/FR-4 Rods
G-10/FR-4 Rods (G10 Rods) are produced from woven glass fabric epoxy laminate sheets which are cut, turned & precision-ground into into rods. Engineered to provide NEMA grade FR-4 properties. This material contains bromine on the epoxy resin backbone. G-10/FR-4 material meets the standard specifications of G-10, but is also UL94V-0, (thus named G-10/FR4). All standard G-10 sold by Professional Plastics is supplied in the premium version of G-10/FR-4 which meets Mil-I-24768/27.
For Non-Brominated G-10, call customer service & specify "G-10, Non-Brominated to meet Mil-I-24768/2.
- Non-Brominated G-10 contains no halogens & is available as a Custom Order Only & is only rated as UL94-HB.
-
G-10/FR-4 Sheets - Sanded
G-10/FR-4 Sheets - Sanded
G-10/FR4 sheets can be sanded to close tolerances for precision requirments. This glass-epoxy laminate is abrasive, but precision sanded sheets are produced using double-disk sanders for your convenience. Please allow 2-5 weeks for sanded sheets.
G-10/FR-4 is a thermosetting industrial laminate consisting of a continuous filament glass cloth material with an epoxy resin binder. It has characteristics of high strength, excellent electrical properties and chemical resistance not only at room temperature but also under humid or moist conditions.
- G-10/FR-4 glass epoxy laminate meets the specifications of Mil-I-24768/27
- G-10 & FR-4 also meet LP 509 & MIL P 18177 Type GEE
-
G-10/FR-4 Sheets
G-10/FR-4 is a thermosetting industrial laminate consisting of a continuous filament glass cloth material with an epoxy resin binder. It has characteristics of high strength, excellent electrical properties and chemical resistance not only at room temperature but also under humid or moist conditions.
- aka G10/FR4, G-10/FR4, FR4 Glass-Epoxy Laminate Sheets
- G-10/FR-4 glass epoxy laminate meets the specifications of Mil-I-24768/27
- G-10 & FR-4 also meet LP 509 & MIL P 18177 Type GEE
- Maximum Continuous Operating Temperature: 285°F
-
G-10/FR-4 Tubes
G-10/FR-4 (G10) is a thermosetting industrial laminate consisting of a continuous filament glass cloth material with an epoxy resin binder. It has characteristics of high strength, excellent electrical properties and chemical resistance not only at room temperature but also under humid or moist conditions. G-10/FR4 epoxy laminate tubes are typically rolled over a mandrel to produce custom-wall thicknesses.
- G-10/FR-4 sheets meet the specifications of Mil-I-24768/27
- G-10/FR-4 also meet LP 509 & MIL P 18177 Type GEE
-
G-11 Rod
G-11 Glass Epoxy Laminate (Mil-I-24768/3) is produced in high-temperature, laminated, glass-cloth sheets. It has high mechanical strength at temperatures up to 150°C, is self extinguishing, and retains 50% of its flexural strength at elevated temperatures. G-11 Rods are manufactured in both "Sheet Rod", which is manufactured by cutting laminated G-11 sheets into strips & the precision ground into rods. We also offer "Rolled & Molded" rods which are produced by rolling epoxy saturated G-11 glass cloth into rods and then pressed and cured into rod molds.
- Standard rods offered on this page are "sheet rods" unless otherwise stated.
-
G-11 Sheets
G-11 Glass Epoxy Laminate (Mil-I-24768/3) is produced in high-temperature, laminated, glass-cloth sheets, as well as, precision-ground rods and rolled and molded tubes. G-11 exhibits high mechanical strength at temperatures up to 150°C, is self extinguishing, and retains 50% of its flexural strength at elevated temperatures.
-
G-11/FR5 - NEMA Grade FR5
FR5 Glass-Cloth Reinforced Epoxy
NEMA grades G11 and FR5 Glass-Cloth Reinforced Epoxy - natural color is typically yellow green to amber. This grade is similar to G10/FR4 but has a higher operating temperature and superior mechanical properties at elevated temperatures. The main difference between NEMA Grades G11 and FR5 is that FR5 is a fire retardant grade of G11.
- Also sold under Norplex Grade MC511AF
-
G-3 (NP-504) Glass-Phenolic Laminate
G-3 Glass-Phenolic Laminate (aka Micarta NP-504) - This woven glass fabric with high-temperature phenolic resin has excellent flexular, compressive, and impact strengths. G-3 can be used for seals, acid-resistant gaskets, oven internals, and various structural applications.
- Available in 36" x 48" Sheets or 48" x 96" Sheets (lead-time may apply).
- Call customer service for less than full-sheet requirements.
-
![G-30 Polyimide Glass Laminate (Norplex P95)]( "G-30 Polyimide Glass Laminate (Norplex P95)")
G-30 Polyimide Glass Laminate (Norplex P95)
G-30 polyimide glass laminate (aka Norplex P95 per NEMA GPY) is a high performance woven glass fabric bonded with polyimide resin. Specially developed to provide engineers with a plastics material capable of continuous long term use at 500°F and higher. Possesses excellent dimensional stability, mechanical and electrical properties which are well maintained at elevated temperatures. Has machining characteristics similar to Grades G10 and G11. G30 (aka Norplex P95-GPY) consists of woven glass fabric with polyimide resin. The product is engineered to maintain excellent physical properties at 240°C, making it suitable for high-temperature applications. It offers a low coefficient of thermal expansion, as well as high mechanical strength and consistent quality. It can be used for structural components, thermal insulators, PCB manufacture and assembly, and high-temperature gaskets in petrochemical plants. P95 complies with the requirements of IEC 60893-3-7-PI GC 301.
-
![G-7 Glass-Silicone Laminate]( "G-7 Glass-Silicone Laminate")
G-7 Glass-Silicone Laminate
G-7 glass-silicon laminate has good electrical properties under humid conditions, excellent heat and arc resistance, and is self-extinguishing. G-7 is used for electrical grade insulation, and for heating & appliance insulation. Silicone laminate grade G7 glass cloth reinforced silicone's natural color is typically cream to white. Composed of a continuous glass woven cloth base impregnates with silicone resin binder, this grade has excellent heat and arc resistance. Silicone thermosets are among the best polymers for high temperature. Hence, silicone is broadly used for high temperature electronic applications requiring low electrical losses. Silicone is not as strong as epoxies and industrial laminates (phenolics), upon aging at lower temperatures but is stronger upon aging over 400 deg F. G7 has extremely good dielectric loss properties under dry conditions and good electrical properties under humid conditions, although the percentage of change is high.
-
G-9 Glass-Melamine Laminate
G-9 Glass-Melamine Laminate is a woven glass fabric that is very hard, flame resistant, and machining grade with excellent electrical properties in high humidity conditions. It has high physical strength and excellent arc resistance. G-9 Glass-Melamine Laminate is produced in sheets, rods and tubes to customer specifications.
-
GlasRod® Fiberglass HIR Rod & Shapes
GlasRod® Fiberglass Solid Rod and Bar products are widely used in electrical, industrial, and construction applications. Shapes include Round Bar, Square Bar, Rectuangular Bar, A Shape & Dog Bone.
GlasRod® products are available in 3 basic grades:
- MTS (Red Color) - most economical for electrical applications. 155° C performance, 50,000 psi tensile strength, 80,000 psi flexural strength.
- Available in Retangle, Square A & Dog Bone Shapes
- SG200 (Tan color) - highest temp (210° C), excellent thermal endurance.
- Available in Retangle, Square A & Dog Bone Shapes
- HIR(Mint Green Color) - highest physical properties. Excellent electrical properties. 200° C Thermal Performance. Dimensional Stability and 100,000 psi Flexular Strength.
-
Glastherm HT200
Glastherm HT200 is a thermal insulating sheet with superior strength and heat resistance for applications with continuous use temperatures up to 550º F. The installation or upgrading of mold base or press platen insulation is one of the highest-returning investments a molding operation can make today. Properly insulated molds require less energy to operate. Adequate insulation also facilitates temperature regulation within the tool.
Glastherm® thermal insulating sheet is an excellent choice for mold insulation applications. Glastherm® sheet offers significant advantages when compared with other materials such as mica, asbestos concrete or calcium silicate. Glastherm® sheet is an efficient thermal barrier and is strong to resist the effects of molding pressure and rough handling. It is resistant to oil and water absorption and is completely asbestos-free.
|
Contact Us
Locations
About Us
Track Shipment
Register
Log In
